How do you feel in regards to How to Install a Bathtub?
Mounting a bathtub isn't precisely rocket science, however it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging task. If the old bathtub is readily available, the task can relocate easily; if you need to open up a wall surface to eliminate the old tub and position the new bathtub, the task is much harder. In either instance, the project is within a residence handyman's abilities, although you will need a helper to leave the old tub and set in the new one. Make sure you have actually qualified on your own for the task and are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed project, it is far better to think about employing one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This write-up will certainly help you mount a brand-new bath tub in your washroom if you have actually already acquired a new bathtub and don't need to change the arrangement of your previous water supply pipes.
Your devices and also product list should make up the following:
Getting ready for the Installation
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted accessibility that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub up until the level checks out level.
To set up faucets, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipe by making a compression join; after that do the same for the other faucet.
Activate the water system and examine all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill the bathtub and likewise inspect the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, deal with the bath paneling as defined in the supplier's user's manual. Tiling and securing around the bath tub ought to wait until the bath tub has actually been utilized at the very least once as this will settle it right into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in area in between the tap as well as the sink. Safeguard the tap in place with the producer supplied backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former type should be attached to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a stiff seal, creating the water to permeate the wall surface between the bathroom and also the tiling, causing complications with moisture and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components and fittings. They are offered in tubes and cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub remains in use. The sealant can fracture rather early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads about Installing A Bathtub, I assumed sharing that excerpt was worthwhile. For those who enjoyed our post plz don't forget to pass it around. Thanks for your time. Visit again soon.
Detail